Colocation costs in Australia: what will you pay over the full contract?

November 13 2026, by Macquarie Technology Group | Category: Data Centres
IC1 colocation data centre

Two colocation quotes can show a similar monthly price and leave you with very different bills. One may include an allowance for power and support; another may charge separately for energy, connections and each engineering task. To compare them fairly, work out what you’ll pay for the same service over the full contract, including the cost of growing or leaving.


This guide gives you a model for comparing colocation proposals without relying on a generic price list. We’ll work through reserved power, energy consumption and the charges that can change the total. You can then test the figures against how your environment is likely to run, rather than assuming day one will look like every month that follows.


What do colocation costs involve?


Colocation costs involve more than just renting rack space in a data centre. Pricing typically includes reserved power capacity, energy consumption, connectivity, cooling and operational support, alongside installation fees, contract increases and potential exit costs. Understanding these components is essential when calculating the total cost of ownership (TCO) and comparing providers.


Put the colocation quotes on the same footing


Providers package space, power and services differently. A rack rate might include a power allowance; another proposal might separate reserved capacity from metered energy. Start by writing down the required service and asking each provider to price it on that basis. Where a bundle cannot be broken down, record what it includes so you do not count the same charge twice.


Then look beyond the initial configuration. More cross connects, extra support work, higher consumption and annual escalation can all change the total. Include them in the model before choosing a provider, while you can still ask questions and negotiate the terms.


Separate reserved capacity from energy use


Power and cooling capacity are important cost drivers, particularly at higher densities, but space and service requirements matter too. Separate the capacity reserved for your equipment, measured in kW, from the energy it consumes over time, measured in kWh. A proposal can charge for both, so an apparently low capacity rate may not represent the complete bill.


For comparable requirements, effective cost per committed kW per month can be a useful summary alongside the full-term total. It is not a substitute for checking inclusions, service levels or usable capacity. If your next refresh increases density, confirm both the cooling options and the price of supporting that configuration in the proposed hall.


Committed capacity versus metered energy


Committed power is capacity reserved under the agreement. Metered energy reflects consumption over a period. Check whether the price includes energy, bills it separately or applies a minimum commitment, and identify any pass-through charges or adjustment mechanisms. Keep these lines separate until you understand the billing basis.


Ask what happens if your demand changes. Can you reduce the commitment, and on what notice? What capacity and charges apply if you exceed it? For A and B feeds, confirm how reserved and usable capacity are defined and how billing works during normal operation and failover. Do not add both feed ratings together and assume that total is available to the equipment.


Compare the same resilience requirement


Check that each quote supports the availability and maintenance arrangements your workloads need. Differences in redundancy, usable power and service boundaries can make a price comparison misleading. Ask providers to explain those differences before putting their totals side by side.


Review relevant facility certification evidence and the actual architecture with your technical team. Tier III addresses concurrent maintainability and Tier IV adds fault tolerance, but the certification scope, application design and contracted service still matter. Compare offers against the same availability requirement rather than assuming a higher Tier is automatically the right purchase.


The costs that surface after signature


Give the recurring service schedules as much attention as the headline price. Connectivity, support, escalation and exit terms can all change the full-term cost, even when they look modest individually.


For cross connects and network access, record installation charges, recurring fees, lead times and any relocation or disconnection costs. Model the connections your architecture is likely to need as it grows. The cost and effort of recreating those connections at another site also belong in your exit planning.


For remote hands, record the included tasks or allowance, billing increments, minimum charges and after-hours rates. Ask what skills are available and whether specialist work costs more. Compare the expected cost of the work you need done, including response and completion commitments, rather than choosing on an hourly rate alone.


Escalation needs to be calculated across the term. A fixed annual increase, a CPI-linked adjustment and a CPI-plus-margin formula can produce different totals. Confirm review dates, floors or caps, and which charges are affected. For variable inputs, state the assumption and test a reasonable range instead of treating a forecast as certain.


Exit costs are easier to clarify before you sign. Check notice periods, early termination provisions, de-installation, make-good requirements and the time allowed to remove equipment. Include any overlap with the next service. These costs affect the practical choices available when you reach renewal.


The colocation comparison model


Use one provider column for each quote. Put recurring costs on the same monthly basis, retain one-off charges separately and calculate the full term with the relevant increases applied. Use the same demand, consumption and service assumptions for every provider. Where information is missing, mark it as unresolved rather than entering zero.

 

Cost category What to record Provider A Provider B
Committed power Reserved kW, charging basis, included energy if any, and monthly capacity charge    
Energy consumption Expected kWh, tariff, pass-through adjustments and any included allowance    
Power redundancy Required topology, usable capacity during failover, and A/B feed billing basis    
Space Racks, cage or suite, and any separate space charge    
Cross connects Installation and recurring charge, multiplied by projected volume    
Remote hands Included allowance, billing increment, standard and after-hours rates    
Installation and migration One-off fit-out, cabling and migration support charges    
Escalation Mechanism, what it applies to, and modelled effect across the term    
Growth and expansion Cost of additional kW, adjacency rights, and density ceiling    
Exit Notice period, make-good and de-installation costs    
Full-term total Recurring costs including energy, escalation and overlap, plus all one-off and exit charges    
Effective cost per kW per month Full-term total divided by total committed kW-months; for constant capacity, committed kW × months    

 

Normalising to a comparable figure


First calculate total cost of ownership for the term: recurring charges, expected energy use, one-off work and exit costs, with escalation applied where relevant. If committed capacity is constant, divide that total by committed kW and the number of months to get an effective cost per committed kW per month. If capacity changes, divide by the sum of each month’s committed kW instead. This is a comparison measure, not an electricity tariff; check the full-term total alongside it.


Run a base case and a growth case using the same demand profile for each provider. Test higher energy consumption, additional connections and support needs, and the cost of spare capacity if growth is slower. A low unit cost can still mean paying for capacity you will not use, so keep the total bill visible.


Account for flexibility and delivery


Service inclusions can have real value when they match how your team works. An appropriate engineering allowance may reduce external call-outs. Available density headroom may avoid a move at the next refresh. Carrier choice may give you more options at network renewal. Put a value on those benefits where you can support the assumptions, and record the ones that remain qualitative.


Also test the cost of a change in plan. If the facility cannot support your future configuration, include the likely work involved in a data centre relocation, with service overlap and project effort. Expansion rights only help if the capacity, timing and commercial terms are clear.


Cost comparison checklist


Confirm each of these in writing before you compare totals.


• Committed capacity in kW, included energy allowance if any, and the basis for metered kWh charges
• Billing and usable capacity for A and B feeds, including failover conditions
• The mechanism and rate for drawing above commitment, and whether headroom exists
• Whether commitment can be reduced, and on what notice
• The redundancy topology each proposal assumes, normalised across all proposals
• Maximum kW per rack supported in the hall offered, and the cost at that density
• Cross connect installation and recurring charges, priced at projected volume
• Remote hands inclusions, billing increments, and after-hours rates
• Whether remote hands staff are directly employed or subcontracted
• Installation, fit-out and migration charges, including any provider-supplied cabling
• The escalation mechanism, what it applies to, and its effect across the full term
• Expansion rights, adjacency reservation, and the price of expansion capacity
• Renewal terms and whether rates reset to market or to a defined mechanism
• Notice period, make-good obligations and de-installation costs at exit
• The contracted service level, its outage definition, exclusions and service credits


Before making the recommendation, ask someone outside the project to follow the calculation from the quote to the total. They should be able to see what is included, which assumptions drive the result and what happens if demand changes. Use those answers alongside the broader data centre selection criteria to judge whether the offer is a good fit.


Looking for a data centre partner that can support your infrastructure today and as your requirements evolve? Macquarie Data Centres provides secure, resilient and scalable data centre solutions for hyperscale, enterprise, government and cloud environments.


Contact us to discuss your requirements, learn more about our team, or request a tour to see our facilities firsthand.


Frequently asked questions


How much does colocation cost in Australia?


It depends on the required space, power capacity, energy use, resilience, term and services. Ask for a quote against a defined configuration, then compare the full-term cost using consistent assumptions. A headline rack rate or kW rate may exclude material charges.


What drives colocation pricing?


Power capacity, energy use and cooling requirements are important drivers, alongside space, service levels, connectivity, support and contract terms. The mix varies by deployment. Separate reserved kW from consumed kWh and record what the provider bundles into each charge.


How do I compare two colocation proposals fairly?


Price the same service and demand profile, identify inclusions, calculate recurring and one-off costs over the full term, and apply the relevant escalation. Compare the total and, where useful, effective cost per committed kW per month. Test growth and lower-demand cases before deciding.


What are the hidden costs in colocation contracts?


Charges that deserve close attention include energy adjustments, additional cross connects, support beyond the included allowance, annual escalation and exit work. They may be disclosed in separate schedules. Ask the provider to show how those schedules affect the configuration you expect to operate.


Is cost per rack or cost per kW the right measure?


Use the measure that makes the same service comparable. Per-rack pricing can be useful when rack power and inclusions match; cost per committed kW per month can help when power allocations differ. Neither is sufficient on its own. Check the full-term total, energy assumptions and usable capacity.


Should I choose the lowest cost provider?


Check what the price includes and whether the service can support your expected needs. Compare operational support, capacity, connectivity and growth terms alongside cost. A lower initial rate may still be good value, but the conclusion should survive a review of the full term and plausible changes in demand.